
Adding a crease or bend to a design often adds strength. However, there are situations where it may negatively impact the final product. Understanding how a radius or chamfer can improve a final thermoplastic part ensures the success of your design.
This discussion shares information included in the Radii and Chamfers section of the Profile Thermoforming Design Guide. Download the guide for additional advice.
Overview: Why you need radii and chamfers
Radius is the amount of rounding added to the edge of a crease or bend. A chamfer is a bevel added to the edge. Properly sized, these design features improve part strength and aesthetics, retain material thickness, even improve manufacturability.
Designers apply them to their parts to ensure the plastic sheet stretches more uniformly over the mold. They minimize stresses and weak points that can result in defects and make it easier to release the thermoformed part from the mold.
A radius creates a smooth transition between two surfaces. Adding it at the bottom of the draw is especially critical. The deeper the part, the larger the radius required. A chamfer softens sharp corners while creating clearance for mating or connecting two parts.
Spotlight: Three-sided corners
A sharp three-sided corner is one of the most difficult features to achieve in thermoforming using a negative mold. It accentuates the draw ratio, the calculated value that helps thermoformers achieve the minimum wall thickness for your ideal part.
As the thermoplastic sheet is pushed into the corner, it’s forced to cover three walls. The material appears to stretch at a geometric rate, causing it to thin out unacceptably. It can even tear and create a hole in the part.
It’s easy to check for thinning. Hold a thermoformed part up to a light source and inspect the corners. If the gauge is too thin, light will be transmitted through the part.
A poorly designed tool that ignores the problem will require using plastic with a heavier starting gauge. Sometimes an adhesive filler can be applied to the inside of the part to strengthen the corner.
Both workaround solutions add significant cost to your part. Properly designed tooling avoids this risk.
Advantages of radii and chamfers
Adding radii or chamfers to your part design prevents having to push the thermoplastic material too deeply into the corners. This stops thinning from occurring and offers other advantages as well.
Compared to a sharp 90-degree corner, a radius or chamfer distributes stress over a larger area. While a chamfer doesn’t distribute stress as well as a radius, it does give a designer the option of using sharp corners at the chamfer’s transition points.
If you need a three-sided corner, apply one large radius with chamfers or smaller radii on the other edges. This is often sufficient to solve the problems of thinning and weakening.
As the draw ratio becomes larger, the radii need to increase. Remember that the ideal corner radius is based on the depth of the part. It helps achieve a more uniform wall thickness, producing consistent parts that avoid cosmetic and performance issues.
The chart below provides a rough approximation of the radius required for different depths.
| Depth of Part | Ideal Corner Radius Range |
| 0″-3″ | 0.015″-0.125″ |
| 3″-6″ | 0.125″-0.250″ |
| 6″-12″ | 0.250″-0.500” |
| Deeper than 12” | Consult a professional thermoformer |
From prototyping to production
Concerned about a critical corner? Prototyping a specific corner or feature of a part design can quickly address questions about material thickness before constructing the tooling.
Designing a plastic part may seem challenging, but partnering with an experienced thermoformer can help. Profile Plastics offers expert design for manufacturing (DFM) assistance to guide you from prototyping through production.
Download the Thermoforming Design Guide for additional information about radii and chamfers.
Profile serves OEMs in industries ranging from healthcare, transportation, material handling, food service, and recreation.
More Tech Articles
-
Designing plastic equipment enclosures for 2027
-
Achieve superior impact resistance with thermoformed parts
-
How thermoforming has recreation and fitness manufacturers covered
-
How materials influence part design in thermoforming
-
The Elements of Part Design
-
Cost Considerations In Designing for Thermoforming
-
Consider process attributes for successful thermoforming
-
How to overcome the challenge of deep draw parts
-
10 Ways to improve plastic component performance and prevent failure
-
Video: The ultimate guide to optimizing part design
